The URL can be used to link to this page

15120180CITY OF CUPERTINO BUILDING PERMIT BUILDING ADDRESS: CONTRACTOR: PERMIT NO: 15120180 10741 N WOLFE RD CUPERTINO CA 95014 (316 45 015) ( HOSPITALITY RENOVATIONS) CEDARTOWN, GA 30125 OWNER'S NAME: QUITO HOSPITALITY ASSCS ETAL DATE ISSUED: 01/27/2016 OWNER'S PHONE: 408-777-8707 PHONE NO: 770-748-6400 LICENSED CONTRACTOR'S DECLARATION BUILDING PERMIT INFO: License Class fl Lic. #978531 Contractor ( HOSPITALITY RENOVATIONS) Date 01/27/2016 — BLDG — ELECT — PLUMB MECH RESIDENTIAL — COMMERCIAL I hereby affirm that I am licensed under the provisions of Chapter 9 (commencing — — with Section 7000) of Division 3 of the Business & Professions Code and that my license is in full force and effect. JOB DESCRIPTION: HILTON GARDEN INN - Remove and replace bathtubs and shower pans I hereby affirm under penalty of perjury one of the following two declarations: with surrounds on all floors, including some accessible bathtubs and showers. 1. I have and will maintain a certificate of consent to self -insure for Worker's Compensation, as provided for by Section 3700 of the Labor Code, for the erformanec of the work for which this permit is issued. i. have and will maintain Worker's Compensation Insurance, as provided for by Section 3700 of the Labor Code, for the performance of the work for which Sq. Ft Floor Area: Valuation: $82000.00 this permit is issued. APPLICANT CERTIFICATION I certify that I have read this application and state that the above Number: Occupancy Type: information is correct. I agree to comply with all city and county 31645 015 316 ordinances and state laws relating to building construction, and hereby authorize representatives of this city to enter upon the above mentioned property for inspection purposes. (We) agree to save indemnify and keep harmless the City of Cupertino against liabilities, judgments, costs, and PERMIT EXPIRES IF WORK IS NOT STARTED expenses which may accrue against said City in consequence of the WITHIN 180 DAYS OF PERMIT ISSUANCE OR granting of this permit. Additionally, the applicant understands and will comply with all non -point source regulations per the Cupertino Municipal 180 DAYS FROM LAST CALLED INSPECTION. Code, Section 9. Issued by: -1 Signature Date 01/27/2016 Date: 01/27/2016 OWNE -BUERVDECI,ARATION RE -ROOFS: I hereby affirm that I am exempt from the Contractor's License Law for one of the All roofs shall be inspected prior to any roofing material being installed. If a roof is following two reasons: installed without first obtaining an inspection, I agree to remove all new materials for 1. I, as owner of the property, or my employees with wages as their sole inspection. compensation, will do the work, and the structure is not intended or offered for sale (Sec.7044, Business & Professions Code) Signature of Applicant: 2. I, as owner of the property, am exclusively contracting with licensed Date: 01/27/2016 contractors to construct the project (Sec.7044, Business & Professions Code). ALL ROOF COVERINGS TO BE CLASS "A" OR BETTER I hereby affirm under penalty of perjury one of the following three declarations: m. I have and will maintain a Certificate of Consent to self -insure for Worker's Compensation, as provided for by Section 3700 of the Labor Code, for the HAZARDOUS MATERIALS DISCLOSURE performance of the work for which this permit is issued. I have read the hazardous materials requirements under Chapter 6.95 of the 2. I have and will maintain Worker's Compensation Insurance, as provided for California Health & Safety Code, Sections 25505, 25533, and 25534. I will by Section 3700 of the Labor Code, for the performance of the work for which maintain compliance with the Cupertino Municipal Code, Chapter 9.12 and the this permit is issued. Health & Safety Code, Section 25532(x) should I store or handle hazardous 3. I certify that in the performance of the work for which this permit is issued, I material. Additionally, should I use equipment or devices which emit hazardous air contaminants as defined by the Bay Area Air Quality Management District I shall not employ any person in any manner so as to become subject to the will maintain compliance with the Cupertino Municipal Code, Chapter 9.12 and Worker's Compensation laws of California. If, after making this certificate of the Health & SafetyCode s 25505, 25533, and 25534. exemption, I become subject to the Worker's Compensation provisions of the Labor Code, I must forthwith comply with such provisions or this permit shall Owner or authorized agent: be deemed revoked. Date: 01/2712016 STRU�T APPLICANT CERTIFICATION I certify that I have read this application and state that the above information is CO I hereby affirm that there is a co traction lending agency for the performance correct. I agree to comply with all city and county ordinances and state laws of work's for which this permit is issued (Sec. 3097, Civ C.) relating to building construction, and hereby authorize representatives of this city Lender's Name to enter upon the above mentioned property for inspection purposes. (We) agree to save indemnify and keep harmless the City of Cupertino against liabilities, Lender's Address judgments, costs, and expenses which may accrue against said City in consequence of the granting of this permit. Additionally, the applicant understands and will comply with all non -point source regulations per the ARCHITECT'S DECLARATION I understand my plans shall be used as public records. Cupertino Municipal Code, Section 9.18. Licensed Professional Signature Date 01/27/2016 aw . CUPERTINO- CONSTRUCTION PERMIT APPLICATION 100180, sicMidw- CONMUNITY DEVELOPMENT DEPARTMENT • BUILDING DIVISION 10300 TORRE AVENUE • CUPERTINO, CA 95014-3255 (408) 777-3228 • FAX (408) 777-3333 • buildinoacuDertino.org F1 laFw rn1,iSTRUCT riv ❑ ADDITION ❑ A.LT=P-kTiON / TI ❑ REVISION / DEFE P D ORIGI-Nd.L PERMTI n PROrcCfADDRFcc .I�� ] ' \ •�, �� I APNn �� 'T� � lwI �fi(/� �� p T OWN-.RIW.0 ��lI,V l I A9351 i0h-upi S REEF A DDRESS ru �.j �}� j� EN � -iTY, 5 rATE ZIP FAX , (� OMEN COlviACT '�',!E pil 'n - I✓ S'2."' ADDR=SSCITY. Z ;^? 14 S�` STA". Z3 FAX R-*'coc.r� trig `31)1251 - ❑ c\i-.- R ❑. OWIv'R-BUII DER ❑ o,; -.=R AC_A'T X CON -IR .CTOR ❑ CON7RACCTTOR!.GT'r ❑ :AC=- ❑ ENGL�zR ❑ D1�APMt ❑ i�1.*f.NT COhZi l �OR1 F.N, �(, N J� R I SO /i% "C�cE?�JN-P=R � / �S3 1 I LiCTS: TYrE I BLS. L C COMPANYNfa�- , , /`�dyAT I F NSII, Qho Re�kxJ FAX o `t' STRrEr ADDRESSthb. 3- I Cr -Y A� TiP,� `�� r &)C\ C �Q + Z D of AI � 5 t -J r�J V`N PiiOhc O -- 6 ' y0 ARCrDiaC'/ENGIN2r_R.NQ, I UCENSEh"l-DIS'R BUS. LIC R' COMPANY NAaM E -W -'.L FAX STFIET ADDR SS I Crry. ST Sia ZIP I ?,qol z DESCRIPTION OF WORK To�� o� S l�� e�✓.2 �i�� iL1-1STLgG UsE PROPOSED USE CONSTR TY?7 k STORE'S I I USE TYPE I OCC. I $Q.FT. VALUATION (S) XISTG NIEV FLOOR DEN40I TOTAL AREA AREA. AREA EA NET AREA BATA-ROOMI YJTCH•-- OTAER i='MODEL!JtEA REMODEL AREA REMODEL f ti.A PORCH AREA DECK AREA I TOTAL DEMMORC-I A RB -A GARAGE AR A: DETACH ❑ ATTACH I RDW_LLINGUNITS. ISASECOND UNIT ❑YES TSECONDSTORY ❑1.S BEING ADDED? [3 )"0 ADDITION? []NO P?"F-•k°PLICATION ❑Y'ss 1 ='PROt4DECOPYOi PL/.N.7 GAPPL. ❑NO ?LA'\NM,GAPPROV/.LL-'HTR IsTHEBLDGAN ❑1SF\ EICHLERHOME? [3 NO Y a. - � .) :OT-.LV?.LU.4TION° Z'D�O By my signature below, I ccertify to each of the follo-., ing: I am the propertyo.>aer or author'ud agent to act on the proper ow er's behalf. I have read this application and the information I have provided is correct. I have read the Description ofWork and veriy it is accurate. I au ee to -comply with all applicable local ordinances and state laws relating to build' onstruction. I authorize representatives -of Cupertino to enter the above -identified property for inspection purposes.SignatureofApplicant/Agent: //:2' Date: ( SLITPLEXIENTAL R1' OR%4ATION REQUIRED New SFD or >,4ultifamily d-,N,ellings: Apply for demolition permit for building(s). Demolition permit is required prior to issiiaace of building ,OYER TFF CO ITER Kexisting permit for new building. PL4�P 4', pry _ Commercial Bldgs: Provide a completed Hazardous Materials Disclosure exD La1� o acs414, Loran if any Hazardous Materials are being used as part of this project. _ Copy of Planning Approval Letter or Meeting with Planning _prior to Imo' z47 'SAT = SE�V�R'DIST.RICT submitta] of Building Permit application. ,» B1c��ap_2011.cec revised 06121/11 ��—�-,, � CITY OF CUPERTINO 15600 F �` / I FEE ESTIMATOR — BUILDING DIVISION NOTE: This estimate does not include fees due to other Departments (i.e. Planning, Public Works, Fire, Sanitary Server District, School ni.ctrirt_ otr-)_ These fees are haled on the nreliminary information available and are only an estimate. Contact the Dept for addn'l info. FEE ITEMS (Fee Resolution 11-053 Eft. 7.-1/13) ADDRESS: 10741 N Wolfe Rd I'Iwnb. Man (,'heck DATE: 12/21/2015 REVIEWED BY: PAUL 1 APN: 316 45 015 BIV: *VALUATION: 1$82,000 ,PERMITTYPE: Building Permit PME Plan Check: PLAN CHECK TYPE: Alteration / Addition / Repair PRIMARY USE: Commercial Building Civil / Religious activities in BQ zone? 0 Yes (F)No PENTAMATION PERMIT TYPE: 1 GE I I i WORK Hilton Garden Inn - 1st Floor / Replace Tub's in Bathrooms; 2nd - 5th Floors / Replace Tub's with SCOPE Shower Pan's PME Unit Fee: NOTE: This estimate does not include fees due to other Departments (i.e. Planning, Public Works, Fire, Sanitary Server District, School ni.ctrirt_ otr-)_ These fees are haled on the nreliminary information available and are only an estimate. Contact the Dept for addn'l info. FEE ITEMS (Fee Resolution 11-053 Eft. 7.-1/13) rlPr''i7. fl! 7,,l C'l7«.'l' I'Iwnb. Man (,'heck MISC ITEMS Plan Check Fee: Hourly Only? ® Yes Q No $0.00 2 hours Plan Check, Hourly $286.00 ISTPLNCK Suppl. PC Fee: (E) Reg. 01' lhh i' Ilio;,h lrcll. —F-1 —I NOTE: This estimate does not include fees due to other Departments (i.e. Planning, Public Works, Fire, Sanitary Server District, School ni.ctrirt_ otr-)_ These fees are haled on the nreliminary information available and are only an estimate. Contact the Dept for addn'l info. FEE ITEMS (Fee Resolution 11-053 Eft. 7.-1/13) FEE QTY/FEE MISC ITEMS Plan Check Fee: Hourly Only? ® Yes Q No $0.00 2 hours Plan Check, Hourly $286.00 ISTPLNCK Suppl. PC Fee: (E) Reg. 01' 0.0 hrs $0.00 PME Plan Check: $0.00 Permit Fee: $0.00 Suppl. Insp. Fee:Q Reg. Q OT0,0 hrs $0.00 PME Unit Fee: $0.00 PME Permit Fee: $0.00 Construction Tax: IBCONSTAXC $0.00 i� rnuislr.,liie Fee: O Work Without Permit? Yes (D No $0.00 Advanced Planning Fee: $0.00 Select a Non -Residential Q Building or Structure i 'rc. �rr,te�jtlrztr?rz I:t..t �: Strong Motion Fee: IBSEISMICO $22.96 Select an Administrative Item Bldg Stds Commission Fee: 1BCBSC $4.00 SUBTOT.aLS: $26.96 $286.00 TOTALFEE: $312.96 Revised: 10/01/2015 CUPERTINO CONTRACTOR / SUBCONTRACTOR LIST Building Department City Of Cupertino 10300 Torre Avenue Cupertino, CA 95014-3255 Telephone: 408-777-3228 Fax: 408-777-3333 JOB ADDRESS: tU741 oLfc RA PERMIT # OWNER'S NAME. A PHONE # -7'70- ?41P. b,/Ap GENERAL CONTRACTOR: BUSINESS LICENSE #4o 12,4 ADDRESS: J49(o -Sohn ,n4 izri CITY/ZIPCODE: C!-edA ar&t00 C'A 3 O a5 *Our municipal code requires all'businesses working in the city to have a City of Cupertino business license. NO BUILDING FINAL OR FINAL OCCUPANCY INSPECTIONS) WILL BE SCHEDULED UNTIL THE GENERAL CONTRACTOR AND ALL SUBCONTRACTORS HAVE OBTAINED A CITY OF CUPERTINO BUSINESS LICENSE. I am not using any subcontractors: Signature Date Please check applicable subcontractors and complete the following information: V SUBCONTRACTOR BUSINESS NAME BUSINESS LICENSE # Cabinets & Millwork Cement Finishing Electrical Excavation Fencing Flooring / Carpeting Linoleum / Wood Glass / Glazing Heating Insulation Landscaping Lathing Masonry Painting / Wallpaper Paving Plastering Plumbing Q� �DLUMSin)Z,O,�a a Roofing Septic Tank Sheet Metal Sheet Rock Tile Owner / Contractor Signature 2-l. i3, i6 Date ACCESSIBILITY TO PUBLIC BUILDINGS, PUBLIC ACCOMMODATIONS, COMMERCIAL BUILDINGS AND PUBLIC HOUSING IIB -607.4.1.1 Back wall. Two grab bars shall be installed on the back wall, one located in accordance with Section 11B-609.4 and the other located 8 inches (203 mm) minimum and 10 inches (254 mm) maximum above the rim of the bathtub. Each grab bar shall be installed 15 inches (381 mm) maximum from the head end wall and 12 inches (305 mm) maximum from the control end wall. IIB -607.4.1.2 Control end wall. A grab bar 24 inches (610 mm) long minimum shall be installed on the con- trol end wall at the front edge of the bathtub. IIB -607.4.2 Bathtubs without permanent seats. For bathtubs without permanent seats, grab bars shall comply with Section 11 B-607.4.2. IIB -607.4.2.1 Back wall. Two grab bars shall be installed on the back wall, one located in accordance with Section 11B-609.4 and the other located 8 inches (203 mm) minimum and 10 inches (254 mm) maximum above the rim of the bathtub. Each grab bar shall be 24 inches (610 mm) long minimum and shall be installed 24 inches (610 mm) maximum from the head end wall and 12 inches (305 mm) maximum from the control end wall. IIB -607.4.2.2 Control end wall. A grab bar 24 inches (610 mm) long minimum shall be installed on the con- trol end wall at the front edge of the bathtub. IIB -607.4.2.3 Head end wall. A grab bar 12 inches (305 mm) long minimum shall be installed on the head end wall at the front edge of the bathtub. 4. LL8-10 203-254 c� € IIB -607.5 Controls. Controls, other than drain stoppers, shall be located on an end wall. Controls shall be between the bathtub rim and grab bar, and between the open side of the bathtub and the centerline of the width of the bathtub. Con- trols shall comply with Section 11 B-309.4. control- . wall lip REVI DA14 FIGURE 11B-607.5 BATHTUB CONTROL LOCATION 11B-607.6 Shower spray unit and water. A shower spray unit with a hose 59 inches (1499 mm) long minimum that can be used both as a fixed -position shower head and as a hand- held shower shall be provided. The shower spray unit shall have an on/off control with a non -positive shut-off. If an adjustable -height shower head on a vertical bar is used, the bar shall be installed so as not to obstruct the use of grab bars. Bathtub shower spray units shall deliver water that is 120°F (49°C) maximum. 15 max 381 back wall control head E end ° end N wall wall (a) (b) elevation plan FIGURE 11B-607.4.1 GRAB BARS FOR BATHTUBS WITH PERMANENT SEATS 12 max 24 min 24 max 3f35 back s10 head (a) (b) N elevation plan FIGURE 11B-607.4.2 GRAB BARS FOR BATHTUBS WITH REMOVABLE IN -TUB SEATS � control end wall m � � end ° N wall c m r 2013 CALIFORNIA BUILDING CODE 587 FOF ACCESSIBILITY TO PUBLIC BUILDINGS, PUBLIC ACCOMMODATIONS, COMMERCIAL BUILDINGS AND PUBLIC HOUSING 11B-607.7 Bathtub enclosures. Enclosures for bathtubs shall not obstruct controls, faucets, shower and spray units or obstruct transfer from wheelchairs onto bathtub seats or into bathtubs. Enclosures on bathtubs shall not have tracks installed on the rim of the open face of the bathtub. IIB -608 Shower compartments 11B-608.1 General. Shower compartments shall comply with Section 11B-608. 11B-608.2 Size and clearances for shower compartments. Shower compartments shall have sizes and clearances com- plying with Section 11B-608.2. 11B-608.2.1 Reserved. IIB -608.2.2 Standard roll -in type shower compart- ments. Standard roll -in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides with a full opening width on the long side. rY, back wall side side wall wall _ O t` M i I Cn i ------------- - 60 min 1524 Note: inside finished dimensions measured at the center points of opposing sides FIGURE 11B-608.2.2 STANDARD ROLL -IN TYPE SHOWER COMPARTMENT SIZE AND CLEARANCE IIB -608.2.2.1 Clearance. A 36 inch (914 mm) wide minimum by 60 inch (1524 mm) long minimum clear- ance shall be provided adjacent to the open face of the shower compartment. Exception: Reserved. 11B-608.2.3 Alternate roll -in type shower compart- ments. Alternate roll -in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides. A 36 inch (914 mm) wide mini- mum entry shall be provided at one end of the long side of the compartment. NJ back wall side ' wall front 36 min wall sf4 M� side wall 60 min 1524 Note: inside finished dimensions measured at the center points of opposing sides FIGURE 11B-608.2.3 ALTERNATE ROLL -IN TYPE SHOWER COMPARTMENT SIZE AND CLEARANCE adjacent walls at a common mounting height, an L-shaped or U-shaped grab bar meeting the dimensional requirements of Section 11B-608.3.2 or 11B-608.3.3 shall be permitted. Exceptions: 1. Reserved. 2. In residential dwelling units, grab bars shall not be required to be installed in showers located in bathing facilities provided that reinforcement has been installed in walls and located so as to permit the installation of grab bars complying with Sec- tion 11 B-608.3. 11B-608.3.1 Reserved. IIB -608.3.2 Standard roll -in type shower compart- ments. Grab bars shall be provided on the back wall and the side wall opposite the seat. Grab bars shall not be pro- vided above the seat. Grab bars shall be installed 6 inches (152 mm) maximum from adjacent walls. 6 max 152 back wall Model code -� figure not x side side applicable E � wall wall or L J (a) (b) reserved with seat FIGURE 118-608.3.2 GRAB BARS FOR STANDARD ROLL -IN TYPE SHOWER 11B-608.3 Grab bars. Grab bars shall comply with Section IIB -609 and shall be provided in accordance with Section IIB -608.3.3 Alternate roll -in type shower compart- IIB-608.3. Where multiple grab bars are used, required hori- ments. In alternate roll -in type shower compartments, zontal grab bars shall be installed at the same height above grab bars shall be provided on the back wall and the side the finish floor. Where separate grab bars are required on wall farthest from the compartment entry. Grab bars shall 588 2013 CALIFORNIA BUILDING CODE ACCESSIBILITY TO PUBLIC BUILDINGS, PUBLIC ACCOMMODATIONS, COMMERCIAL BUILDINGS AND PUBLIC HOUSING not be provided above the seat. Grab bars shall be installed 6 inches (152 mm) maximum from adjacent walls. 6 max 6 max 152 152 back wall side X� side Wall E' wall - - - '1 front wall FIGURE 11B-608.3.3 GRAB BARS FOR ALTERNATE ROLL -IN TYPE SHOWERS IIB -608.4 Seats. A folding seat shall be provided in roll -in type showers. Seats shall comply with Section IIB -610. Exception: In residential dwelling units, seats shall not be required in shower compartments provided that reinforce- ment has been installed in walls so as to permit the instal- lation of seats complying with Section 11 B-608.4. IIB -608.5 Controls. Controls, faucets, and shower spray units shall comply with Section IIB -309.4. Controls and fau- cets shall be of a single -lever design. IIB -608.5.1 Reserved. IIB -608.5.2 Standard roll -in type shower compart- ments. In standard roll -in type shower compartments, operable parts of controls and faucets shall be installed on the back wall of the compartment adjacent to the seat wall 19 inches (483 mm) minimum and 27 inches (686 mm) maximum from the seat wall; and shall be located above the grab bar, but no higher than 48 inches (1219 mm) above the shower floor, with their centerline at 39 inches (991 mm) to 41 inches (1041 mm) above the shower floor. Operable parts of the shower spray unit, including the handle, shall be installed on the back wall adjacent to the seat wall 19 inches (483 mm) minimum and 27 inches (686 Model code figure not applicable (a) reserved 27 max 666 19 mi back wall (b) with seat FIGURE 11B-608.5.2 STANDARD ROLL -IN TYPE SHOWER COMPARTMENT CONTROL LOCATION x E mm) maximum from the seat wall; and shall be located above the grab bar, but no higher than 48 inches (1219 mm) above the shower floor. IIB -608.5.3 Alternate roll -in type shower compart- ments. In alternate roll -in type shower compartments, operable parts of controls and faucets shall be installed on the side wall of the compartment adjacent to the seat wall 19 inches (483 mm) minimum and 27 inches (686 mm) maximum from the seat wall; and shall be located above the grab bar, but no higher than 48 inches (1219 mm) above the shower floor, with their centerline at 39 inches (991 mm) to 41 inches (1041 mm) above the shower floor. Operable parts of the shower spray unit, including the handle, shall be installed on the side wall of the compart- ment adjacent to the seat wall 17 inches (432 mm) mini- mum and 19 inches (483 mm) maximum from the seat wall or on the back wall opposite the seat 15 inches (381 mm) maximum, left or right, of the centerline of the seat; and shall be located above the grab bar, but no higher than 48 inches (1219 mm) above the shower floor. 11B-608.6 Shower spray unit and water. A shower spray unit with a hose 59 inches (1499 mm) long minimum that can be used both as a fixed -position shower head and as a hand- held shower shall be provided. The shower spray unit shall have an on/off control with a non -positive shut-off. If an adjustable -height shower head on a vertical bar is used, the bar shall be installed so as not to obstruct the use of grab bars. Shower spray units shall deliver water that is 120T (49°C) maximum. Exception: Where subject to excessive vandalism, two fixed shower heads shall be installed instead of a hand- held spray unit in facilities that are not transient lodging guest rooms. Each shower head shall be installed so it can be operated independently of the other and shall have swivel angle adjustments, both vertically and horizontally. 27 max e86 15 max 19 min 3B1 483 m side back E;; wall wall E co I 00 0 � I (a) I (b) (elevation) (elevation) Model code side figure not wall applicable (c) reserved (d) (plan) FIGURE 11B-608.5.3 ALTERNATE ROLL -IN TYPE SHOWER COMPARTMENT CONTROL LOCATION de rail 2013 CALIFORNIA BUILDING CODE 589 ACCESSIBILITY TO PUBLIC BUILDINGS, PUBLIC ACCOMMODATIONS, COMMERCIAL BUILDINGS AND PUBLIC HOUSING 11B-608.7 Thresholds. Thresholds in roll -in type shower Exceptions: compartments shall be i/2 inch (12.7 mm) high maximum in 1. The space between the grab bars and shower con - accordance with Section 11B-303. trols, shower fittings, and other grab bars above Exception: Reserved shall be permitted to be 1'/2 inches (38 mm) mini - IIB -608.8 Shower enclosures. Enclosures for shower com- partments shall not obstruct controls, faucets, and shower spray units or obstruct transfer from wheelchairs onto shower seats. IIB -608.9 Shower floor or ground surface. Floor or ground surfaces of showers shall comply with Section IIB -302.1 and shall be sloped 1:48 maximum in any direction. Where drains are provided, grate openings shall be % inch (6.4 mm) maxi- mum and flush with the floor surface. IIB -608.10 Soap dish. Where a soap dish is provided, it shall be located on the control wall at 40 inches (1016 mm) maximum above the shower floor, and within the reach limits from the seat. IIB -609 Grab bars IIB -609.1 General. Grab bars in toilet facilities and bathing facilities shall comply with Section IIB -609. IIB -609.2 Cross section. Grab bars shall have a cross sec- tion complying with Section IIB -609.2.1 or 11B-609.2.2. IIB -609.2.1 Circular cross section. Grab bars with circu- lar cross sections shall have an outside diameter of 1'/4 inches (32 mm) minimum and 2 inches (51 mm) maxi- mum. 11B-609.2.2 Non -circular cross section. Grab bars with non -circular cross sections shall have a cross-section dimension of 2 inches (51 mm) maximum and a perimeter dimension of 4 inches (102 mm) minimum and 4.8 inches (122 mm) maximum. 4-4.8 f 2 max 51 (a) (b) FIGURE 11B-609.2.2 GRAB BAR NON -CIRCULAR CROSS SECTION IIB -609.3 Spacing. The space between the wall and the grab bar shall be 1'/2 inches (38 mm). The space between the grab bar and projecting objects below and at the ends shall be 1'/2 inches (38 mm) minimum. The space between the grab bar and projecting objects above shall be 12 inches (305 mm) minimum. MUM. 2. For L-shaped or U-shaped grab bars complying with Section 11B-609.9 the space between the walls and the grab bar shall be P12 inches (38 mm) mini- mum for a distance of 6 inches on either side of the inside corner between two adjacent wall surfaces. c � a N " 1'/2 min x __ (a) (b) projecting objects recessed objects FIGURE 11B-609.3 SPACING OF GRAB BARS IIB -609.4 Position of grab bars. Grab bars shall be installed in a horizontal position, 33 inches (838 mm) minimum and 36 inches (914 mm) maximum above the finish floor measured to the top of the gripping surface, except that at water closets for children's use complying with Section 11 B-604.9, grab bars shall be installed in a horizontal position 18 inches (457 mm) minimum and 27 inches (686 mm) maximum above the finish floor measured to the top of the gripping surface. The height of the lower grab bar on the back wall of a bathtub shall comply with Section 1IB-607.4. 1.1 or IIB -607.4.2. 1. IIB -609.5 Surface hazards. Grab bars and any wall or other surfaces adjacent to grab bars shall be free of sharp or abra- sive elements and shall have rounded edges. IIB -609.6 Fittings. Grab bars shall not rotate within their fit- tings. I1B-609.7 Installation. Grab bars shall be installed in any manner that provides a gripping surface at the specified loca- tions and that does not obstruct the required clear floor space. IIB -609.8 Structural strength. Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the grab bar, fastener, mounting device, or supporting structure. IIB -609.9 Alternate configuration. L-shaped or U-shaped grab bars shall be permitted. IIB -610 Seats IIB -610.1 General. Seats in bathtubs and shower compart- ments shall comply with Section 11B-610. IIB -610.2 Bathtub seats. The top of bathtub seats shall be 17 inches (432 mm) minimum and 19 inches (483 mm) maxi - 590 2013 CALIFORNIA BUILDING CODE